May 2020 - Artisan-User - lists.einfachkaffee.de

Victor 86B multi meter as device, how to set up?

by Henrik Bo Carlsen

Hi, On the device page https://artisan-scope.org/devices/meters/ I read that the optically isolated Victor 86B is compatible with Scope, while others say Scope do not work with USB HID devices, such as the Victor DMM.... My Victor 86B shows up in the device manager under USB HID devices in win 7. In Artisan 2.0.0 Scope config devices is set to Meter/Victor 86B after which a port config window appears to select a com port. I have installed the CP210X driver, and would expect a virtual comport to show up, when the Victor 86B is connected, but that does not seem to happen. Any suggestions to cure the problem, please let me know. Alternatively, for two K-type sensors, which optically isolated solution is the choice for Artisan Scope 2.0.0, please. Thanks in advance, Henrik

3 months, 1 week

4
4
0 0

Batch number?

by Dennis Garrett

Recently the batch numbers reset to 0 and started counting up again. I try to change it back, but it won't stick. How can I set the Batch counter back to the correct number? Config...Batch... is not working. Dennis

6 months, 1 week

3
19
0 0

Artisan 2.1.3 Unable to claim interface - Aillio Bullet

by Stuart McKnight

Upgraded to 2.1.3/2.4RC3 and although the legacy USB drivers are installed and the Aillio is connecting to the legacy Roast Time software (not V2) getting “Unable to claim interface” error. Does Artisan use a virtual COM port to connect ? The libusb properties do not show any COM port setting. Thought maybe it was a edge case issue with 2.4RC but reverting back to 2.1.2 gives the same problem or a message about a pipe. Tried uninstalling driver(s), having the Aillio as the only USB attached device, restarted Windows 10 several times. Still same problem, Aillio software can see the machine but Artisan appears blind. I don’t think the message is a benign error as the LCDs and Buttons do not show correct values or control machine. Please don’t make me go back to the proprietary software ;-)

7 months, 3 weeks

6
14
0 0

Anyone with a FZ-94 and experience on comms?

by Brett Pound

I have a colleague who has an FZ-94 and has never had reliable communications from it to a PC (or a mac) since they bought it (2nd hand, I understand). I don’t have much detail right now, but has anyone seen or had any issues like this with an FZ-94? Any thoughts on where to start troubleshooting ? I’ll be assisting remotely so any tips at all would be appreciated ! Cheers Brett Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10

7 months, 3 weeks

2
1
0 0

Controling the heater of a Quest M3

by mario.eduardo＠vetmeduni.ac.at

i want to control the heater of my Quest M3. I have an idea (using a proportinal control SSR and an OUT1001). But such an SSR costs about €100. Is there a way to do this in a simpler way? Any experience ?? Mario

7 months, 3 weeks

2
1
0 0

Programming Python

by mario.eduardo＠vetmeduni.ac.at

Sorry for a post about programming, artisan users could have this problem if ... they want to program a phidget with python. in what way must i start ironpython to access the phidget22 modules. they must be present, but sorry, i am new to python. Mario

7 months, 3 weeks

1
0
0 0

Re: v2.4 Release Candidate

by Frans Goddijn

Happy to help! Frans > Van: Dan Coplan <dan(a)fatrabbitcoffee.com> > Datum: 23 mei 2020 om 19:02:05 CEST > Aan: Frans Goddijn <frans(a)goddijn.com> > Onderwerp: Antw: [Artisan-user] v2.4 Release Candidate > > Thanks for sending the video. Ok, I kind of figured out what’s going on. The beep function does work after all but somehow the alert sounds within my system (I’m on a Mac as well) go silent after a while. The speakers still work, the voices play fine, but the alerts just stop. I restarted my computer and all works fine and I expect it to continue to work fine…until it doesn’t. Anyway, minor issue but glad I got that figured out and with your help. Much appreciated. > > Dan > > Fat Rabbit Coffee > dan(a)fatrabbitcoffee.com <mailto:dan@fatrabbitcoffee.com> > www.fatrabbitcoffee.com <http://www.fatrabbitcoffee.com/> > >> On May 23, 2020, at 7:25 AM, Frans Goddijn via Artisan-User <artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>> wrote: >> >> I’ve sent you a screen video of mine: >> https://we.tl/t-bdJp4N9F3W <https://we.tl/t-bdJp4N9F3W> >> >> I selected the “beep”, then selected what sound I want to associate with that in my laptop OS. Like selecting what voice and volume for that voice, it depends on what your computer offers you in options. >> >> Frans >> >>> Op 23 mei 2020, om 15:55 heeft Dan Coplan via Artisan-User <artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>> het volgende geschreven: >>> >>> Thanks Frans that was very helpful. In Alarms, does the Beep function do anything? I have it checked for all my alarms but have never heard any kind of beep. Not a big deal, but I would love a way to program in a more noticeable (annoying even) buzzer to really get my attention. >>> >>> Fat Rabbit Coffee >>> dan(a)fatrabbitcoffee.com <mailto:dan@fatrabbitcoffee.com> >>> www.fatrabbitcoffee.com <http://www.fatrabbitcoffee.com/> >>> >>>> On May 22, 2020, at 12:13 AM, Frans Goddijn via Artisan-User <artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>> wrote: >>>> >>>> I did a couple of roasts with this version, all went perfectly as well. >>>> >>>>> 1. I have a couple alarms set up that use artificial speech to notify me but they’re pretty quiet even with the volume turned all the way up. >>>> >>>> In my Alarms, this is done by a command to the computer: "say -v samantha Started. Full power, Drum ninety, Fan one” — and it’s up to computer to handle the volume. My Macbook can be pretty loud. And there’s third party software that can boost that volume even more. >>>> >>>>> 3. Is there a way to preset Gas and Fan data so it’s the same for every single roast? I always start my roasts with Fan=40 and Gas=10. I can click these buttons of course or add them at the end but having a template for this would save a step. >>>> >>>> At ON, the Alarms file here activates the buttons for the settings that I want (and speaking "say -v samantha Started. Full power, Drum ninety, Fan one”). You could do that for Fan=40 and Gas=10. >>>> >>>> Frans >>>> _______________________________________________ >>>> Artisan-User mailing list -- artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de> >>>> To unsubscribe send an email to artisan-user-leave(a)lists.einfachkaffee.de <mailto:artisan-user-leave@lists.einfachkaffee.de> >>>> unsubscribe via https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe… <https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe…> >>> >>> _______________________________________________ >>> Artisan-User mailing list -- artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de> >>> To unsubscribe send an email to artisan-user-leave(a)lists.einfachkaffee.de <mailto:artisan-user-leave@lists.einfachkaffee.de> >>> unsubscribe via https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe… <https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe…> >> >> _______________________________________________ >> Artisan-User mailing list -- artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de> >> To unsubscribe send an email to artisan-user-leave(a)lists.einfachkaffee.de <mailto:artisan-user-leave@lists.einfachkaffee.de> >> unsubscribe via https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe… <https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe…> >

7 months, 4 weeks

3
2
0 0

Re: control phidget out 1001 12 bit

by Marko Luther

Dear Guy, > On 23. May 2020, at 20:08, Guy Tzur <espressotech(a)gmail.com> wrote: > > Hi > well now i am in practice. > > i have installed VINT TMP1101 2x TC Set and configured machine type phidget tmp1101 2xTC > where i connected OUT1001_0 for controlling gas proportional valve to port 0 of hub 0000_0 > and rel1100_0 for controlling fan to port 5 channel of both is 0 as appeared in control panel. Ok. Which port is the TMP1101 connected too? > i defined hub IO 0 as extra device see attached pic ,but there is no option to put hub IO 05 i can connect to another port if necessary . WHY? Your OUT1001 and your REL1100 are output devices. You don't want to read data from then, right? So why configure an extra device for them. You "HUB IO 0" extra device is attaching to port 0 of the HUB0000 and blocking it for any other use. Thus Artisan cannot send commands to the connected OUT1001 port 0 to drive your valve. According to its specification, the OUT1101 can send out a voltage from 0-4.2V. Phidget wrote an excellent documentation on this module (as they do for all modules). https://www.phidgets.com/?tier=3&catid=2&pcid=1&prodid=711 The VOUT Command "out(<port>,<value>)" outputs the given <value> in Volt on the given <port>. The OUT1101 has only one port, thus <port> needs to be 0. The <value> needs to range from 0-4.2V. You are putting a 10 in here. WHY? Note that you do not put a serial number if you only have one OUT1101 connected to your system. Thus your VOUT Command should read out(0,{}) The placeholder {} will be replaced by your slider value. Now you have to limit that slider value to the range of this module, 0-4.3. I suggest to keep the slider min/max limits to 0 and 100, but use a factor of 4.3/100 = 0.043, thus moving the slider to 100 will bind the placeholder {} to 100*0.043, which is the maximum voltage supported by the OUT1101, which is 4.3V. For the REL1100 you use the PWM Command "out(0,{})" to drive the first port via a PWM of 0-100 using the sliders default offset of 0 and factor of 1 and range of 0-100. > > and put commands like you recommend on events see attached pic > while each phidget is working properly in the phidget control panel > they are not working from the slider air or burner. > i switch off phidget control panel as i understand it cannot work together with artisan > first Yes. In a networking configuration Artisan can work in parallel with the Phidgets Control Panel app, but this extra complication is usually not needed. Thus it is better to use the standard direct communication and live with this limitation of the Phidgets driver. > i tried with 2.1.2 version and the proportional valve did not react at all i installed version 2.1.3 and > the valve opened to max 10 volt and stayed there the slider did not change anything and fan on both versions is not active at all > can you advice ? Download and install the just released Artisan v2.4.0 RC. It reports itself as v2.1.3, but will soon be released as v2.4. > another question: is every time i open artisan i should configure the machine again? No, of course not. App settings are saved in your system. Hope this helps, Marko > regards > Guy > > 2 קבצים מצורפים > > > > > On Thu, Dec 19, 2019 at 1:21 PM Marko Luther <marko.luther(a)gmx.net> wrote: > Dear Guy, > > > On 18. Dec 2019, at 21:09, Guy Tzur via Artisan-User <artisan-user(a)lists.einfachkaffee.de> wrote: > > > > Hello > > i understand that phidget TMP1101_0 - 4x Thermocouple Phidget can be configured with tools menu to control et temperature > > what if i want to add out 1001 12 bit to control proportional valve > > do i have to add slider commands ? i did not find this phidget in the menu > > Yes you have to add slider or button commands. Output Phidgets are documented in the post "More Phidgets!" on the Artisan blog. > > https://artisan-roasterscope.blogspot.com/2017/12/more-phidgets.html > > The OUT1001 is an analog voltage output device, thus you need to use an "VOUT Command" action with the command "out(n,v)" where n is the channel of the OUT1001 you want to address and v is the output value in V. > > > also regarding phidget out 1100 4x digital if i would like to control fan with it where do i add it in Artisan and how? > > The OUT1100 is a digital voltage output device which supports PWM. Thus you need to use the "PWM Command" action with the command "out(<n>,<v>)", where again n is the channel of the OUT1100 you want to address and n is the intended PWM level 0-100%. > > Hope this helps, > M > > > regards > > Guy > > > > -- > > best regards > > Guy Tzur > > > > www.espressotech.co.il > > _______________________________________________ > > Artisan-User mailing list -- artisan-user(a)lists.einfachkaffee.de > > To unsubscribe send an email to artisan-user-leave(a)lists.einfachkaffee.de > > unsubscribe via https://mailman.ghostdub.de/postorius/lists/artisan-user.lists.einfachkaffe… > > > > -- > best regards > Guy Tzur > > www.espressotech.co.il > <hub define.JPG><event.JPG>

8 months

1
0
0 0

v2.4 Release Candidate

by Marko Luther

Dear all, we have been busy the past month putting together a new version of Artisan. As we changed many things we would like to ask the more experienced Artisan users to give our Release Candidate a test and report issues and suggestions for further refinements before we release this version to the general public. https://github.com/artisan-roaster-scope/artisan/releases/tag/v2.4.0-RC There are versions for Linux (Redhat/Debian), Windows, macOS, Raspian Stretch (RPi) and now also for the current Raspian Buster (RPi). You can install this as any other version. It is compatible with previous and future release and as always, your Artisan settings are preserved on installation. If things do not work out they should you can simply install the last release v2.1.2 again. Still it is advisable to save your Artisan settings with your current installation (menu Help >> Save Settings) into an artisan-settings.aset file to be able to reload that if things go wrong or you played with settings. The download link above links to the already available documentation of some new features. A later post will provide proper release notes as always. The full list of changes w.r.t. the previous versions is documented in the Detailed Release History: https://github.com/artisan-roaster-scope/artisan/blob/master/wiki/ReleaseHi… Thanks for your support on testing our RC! We are awaiting your reports either on this mailing list or via our Issue Tracker: https://github.com/artisan-roaster-scope/artisan/issues The Artisan team

8 months

3
6
0 0

Artisan 2.1.2 dependency problem

by sawbona＠xsmail.com

Hello: I am attempting to install artisan-linux-2.1.2_raspbian-stretch to my Raspberry Pi 3B+. [code] groucho@rpidevuan:~$ uname -a Linux rpidevuan 4.16.14-v8+ #1 SMP PREEMPT Tue Jun 5 18:50:10 CEST 2018 aarch64 GNU/Linux groucho@rpidevuan:~$ [/code] I get a dependency error to whch I cannot find a solution to: [code] root@rpidevuan:/home/groucho/Downloads# dpkg -i artisan-linux-2.1.2_raspbian-stretch.deb Selecting previously unselected package artisan:armhf. (Reading database ... 37452 files and directories currently installed.) Preparing to unpack artisan-linux-2.1.2_raspbian-stretch.deb ... Unpacking artisan:armhf (2.1.2) ... dpkg: dependency problems prevent configuration of artisan:armhf: artisan:armhf depends on libc6 (>= 2.17). dpkg: error processing package artisan:armhf (--install): dependency problems - leaving unconfigured Processing triggers for mime-support (3.60) ... Errors were encountered while processing: artisan:armhf root@rpidevuan:/home/groucho/Downloads# [/code] I thought to solve the issue by installing libc6-armhf-cross but I also get an error: [code] root@rpidevuan:/home/groucho# apt-get install libc6-armhf-cross Reading package lists... Done Building dependency tree Reading state information... Done You might want to run 'apt --fix-broken install' to correct these. The following packages have unmet dependencies: artisan:armhf : Depends: libc6:armhf (>= 2.17) but it is not installable E: Unmet dependencies. Try 'apt --fix-broken install' with no packages (or specify a solution). root@rpidevuan:/home/groucho# [/code] Running *apt --fix-broken install* gets rid of artisan:armhf but that does not solve the problem, which apparently needs an uninstallable library ie: libc6:armhf Any idea as how to fix this? Thanks in advance, J.

8 months

2
1
0 0

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

Artisan-User May 2020