I'm relatively new to artisan. Been using RoastLogger for years but now that
I have my phidget 1048 I don't need the camera/ocr feature anymore.
I haven't been able to locate the help file or information about the
settings under Config-Device - Phidgets tab. For instance, Async check
boxes, raw data, change etc. I've found everything on the github page, but
maybe I just haven't been successful in pinpointing the proper area to look.
Secondly- I'm roasting on a Diedrich IR-24, which has a thicker J
thermocouple than the one I've hooked up to artisan, which is a K type 1/8in
I purchased here:
https://www.automationdirect.com/adc/Shopping/Catalog/Sensors_-z-_Encoders/T
emperature_Sensors_-a-_Transmitters/Thermocouple_Sensors/Probes_(with_Lead_W
ire_Transition)/THMK-T06L06-01
The temperatures are around 30 degrees F higher on the thinner K
thermocouple than what the roaster is reporting, even though my
thermocouples in the roaster are mounted next to each other (didn't want to
piggyback on BT of the roaster to phidgets)
Does anyone have any experience in this area? Perhaps the simple fact that
the probe is thinner means the readings will be different, but I do not
know. It would appear that the readings on the roaster are accurate while
the other is much hotter.
Just getting started, and appreciate any guidance.
Hi Everyone,
I'm attempting to control my gas using a Phidgets OUT1001_0 via a VINT Hub0000_0.
I using MAC 10.14.4, Artisan 1.6.2 and Phidgets 22.
I've created a slider with the following settings:
VOUT Command, out(0,{}), Offset 0.0, Factor 0.1 (For 10V control) min: 0 Max 100.
Device Assignment:
Meter - Phidget TMP 1101 4xTC 01
Extra Devices - Phidget HUB 0000 IO 01
My valve works when using the Phidget Control Panel slider and shows the OUT1001_0 is using Channel 0 and Hub Port 1.
Any ideas?
Hi there,
quick question, thinking of setting up a Huky 500T and getting Artisan.
I read through the quick set up blog and looking through the supported roasters, the Huky 500 does not show up .. and yet I also saw your blogpost re. automating the Huky.
Can you please advise?
Also, I’d like to set it up with either the phidget 1048 or the Vint you described in the Huky post.
I’m not as electronically savvy as you :) and don’t think I would also add the slider for the airflow control ( although it makes a lot of sense .. but I get lost in set ups ..sadly!
which of the two would you recommend the 1048 or the Vint?
I would to start off anyway, simply use the 2 thermocouples ET & BT
PS : have an manual dimmer switch slider attached to the fan though :)
Thanks
best wishes,
Elizabeth
Café do Gatto <cafedogatto(a)gmail.com>
11:57 (há 1 minuto)
para artisan-user-confirm+675daa0fb89d4906d61869e661c4c719da248a5a
Bom dia,
Tenho um torrador Atilla 5Kg Gold Plus, estou tentando instalar ele mas
está dando erro,
identifiquei o modelo Atilla gold plus 7, fiz Porta de Comunicação
COM5,Litthe-Edian ( x bites) (Words) no restante não modifiquei nada.
Sempre dá erro, usei a versão para Windows
muito obrigado, aguardo seu retorno,
Gilmar Wathier Nunes
051 997825005