I'm relatively new to artisan. Been using RoastLogger for years but now that
I have my phidget 1048 I don't need the camera/ocr feature anymore.
I haven't been able to locate the help file or information about the
settings under Config-Device - Phidgets tab. For instance, Async check
boxes, raw data, change etc. I've found everything on the github page, but
maybe I just haven't been successful in pinpointing the proper area to look.
Secondly- I'm roasting on a Diedrich IR-24, which has a thicker J
thermocouple than the one I've hooked up to artisan, which is a K type 1/8in
I purchased here:
https://www.automationdirect.com/adc/Shopping/Catalog/Sensors_-z-_Encoders/T
emperature_Sensors_-a-_Transmitters/Thermocouple_Sensors/Probes_(with_Lead_W
ire_Transition)/THMK-T06L06-01
The temperatures are around 30 degrees F higher on the thinner K
thermocouple than what the roaster is reporting, even though my
thermocouples in the roaster are mounted next to each other (didn't want to
piggyback on BT of the roaster to phidgets)
Does anyone have any experience in this area? Perhaps the simple fact that
the probe is thinner means the readings will be different, but I do not
know. It would appear that the readings on the roaster are accurate while
the other is much hotter.
Just getting started, and appreciate any guidance.
Dear all,
I received many complaints on noisy RoR signals over the year. The ongoing work of Scott Rao and a broken TC made me reconsider my own roast logging setup. As I had collected many different meters and probes over the years, mostly for development purpose, I wonder which one I should best install in my machine.
My goal was to minimize both, the signal to noise ratio as well as the introduced signal delay, especially for the RoR. Thus I came up with a setup that would allow me to compare different setups on the amount of idle noise they produce.
Details are here: https://artisan-roasterscope.blogspot.com/2019/03/on-idle-noise.html
I switched from TCs to RTDs for reasons detailed in the post and I am quite happy with my new setup,
Marko
Hi everyone:
My roaster is apart for mods and it is getting to the point that I
could take advantage of a second another VINT hub. I just want to
check if that is possible, please.
Also, I noticed that there is no mention of Phidget 1136 (diff. air
pressure) on the supported devices page. Has support been dropped?
Kind regards,
-Craig
--
---
- Craig Seko
The info you provide is very terse.
“SF6” is probably http://www.sanfranroaster.com/sf-6lb <http://www.sanfranroaster.com/sf-6lb>
And “Watlow" I assume to mean http://www.watlow.com/products/controllers/temperature.cfm <http://www.watlow.com/products/controllers/temperature.cfm>
My hunch is you maybe just connected the cables without making sure that variables like baud speed, even/uneven, parity, stopbits are all set exactly the same on both ends.
SF should be providing that info / assistance in their manuals / service desk.
Frans
> Op 29 sep. 2015, om 02:28 heeft Nate White <wcrcompany(a)gmail.com> het volgende geschreven:
>
> Which is Modbus Error: readfloat() Modbus Error: [connection] failed to connect [rtu baud[9600]] Aline 23885
>
> This is on an SF6 with Watlow. I'm sure this is a stupid question, my apologies.
>
> Nate
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> https://lists.mokelbu.de/listinfo/artisan-user
Dear Marko,
here the Phidget ‘ambient’ devices seem not to be communicating…
I just spotted this late tonight. Tomorrow I’m off for 2 days.
It’s no a problem here but maybe it’s not just my system where this stopped.
F