I'm relatively new to artisan. Been using RoastLogger for years but now that
I have my phidget 1048 I don't need the camera/ocr feature anymore.
I haven't been able to locate the help file or information about the
settings under Config-Device - Phidgets tab. For instance, Async check
boxes, raw data, change etc. I've found everything on the github page, but
maybe I just haven't been successful in pinpointing the proper area to look.
Secondly- I'm roasting on a Diedrich IR-24, which has a thicker J
thermocouple than the one I've hooked up to artisan, which is a K type 1/8in
I purchased here:
https://www.automationdirect.com/adc/Shopping/Catalog/Sensors_-z-_Encoders/T
emperature_Sensors_-a-_Transmitters/Thermocouple_Sensors/Probes_(with_Lead_W
ire_Transition)/THMK-T06L06-01
The temperatures are around 30 degrees F higher on the thinner K
thermocouple than what the roaster is reporting, even though my
thermocouples in the roaster are mounted next to each other (didn't want to
piggyback on BT of the roaster to phidgets)
Does anyone have any experience in this area? Perhaps the simple fact that
the probe is thinner means the readings will be different, but I do not
know. It would appear that the readings on the roaster are accurate while
the other is much hotter.
Just getting started, and appreciate any guidance.
The info you provide is very terse.
“SF6” is probably http://www.sanfranroaster.com/sf-6lb <http://www.sanfranroaster.com/sf-6lb>
And “Watlow" I assume to mean http://www.watlow.com/products/controllers/temperature.cfm <http://www.watlow.com/products/controllers/temperature.cfm>
My hunch is you maybe just connected the cables without making sure that variables like baud speed, even/uneven, parity, stopbits are all set exactly the same on both ends.
SF should be providing that info / assistance in their manuals / service desk.
Frans
> Op 29 sep. 2015, om 02:28 heeft Nate White <wcrcompany(a)gmail.com> het volgende geschreven:
>
> Which is Modbus Error: readfloat() Modbus Error: [connection] failed to connect [rtu baud[9600]] Aline 23885
>
> This is on an SF6 with Watlow. I'm sure this is a stupid question, my apologies.
>
> Nate
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> https://lists.mokelbu.de/listinfo/artisan-user
Liebe An-Luftschloss-Schreibende
Das Kaffeehaus macht Ferien. Wir sind ab dem 7. August wieder für euch da mit frisch geröstetem Kaffee.
Während dieser Zeit werden die e-Mails nur sporadisch abgerufen und beantwortet. Danke für eure Geduld.
Kulturschaffende informieren sich auf https://kaffeehaus.sg/kultivierter/
Besten Dank und herzliche Grüsse
Gallus Hufenus & Team
Liebe An-Luftschloss-Schreibende
Das Kaffeehaus macht Ferien. Wir sind ab dem 7. August wieder für euch da mit frisch geröstetem Kaffee.
Während dieser Zeit werden die e-Mails nur sporadisch abgerufen und beantwortet. Danke für eure Geduld.
Kulturschaffende informieren sich auf https://kaffeehaus.sg/kultivierter/
Besten Dank und herzliche Grüsse
Gallus Hufenus & Team
Liebe An-Luftschloss-Schreibende
Das Kaffeehaus macht Ferien. Wir sind ab dem 7. August wieder für euch da mit frisch geröstetem Kaffee.
Während dieser Zeit werden die e-Mails nur sporadisch abgerufen und beantwortet. Danke für eure Geduld.
Kulturschaffende informieren sich auf https://kaffeehaus.sg/kultivierter/
Besten Dank und herzliche Grüsse
Gallus Hufenus & Team
Liebe An-Luftschloss-Schreibende
Das Kaffeehaus macht Ferien. Wir sind ab dem 7. August wieder für euch da mit frisch geröstetem Kaffee.
Während dieser Zeit werden die e-Mails nur sporadisch abgerufen und beantwortet. Danke für eure Geduld.
Kulturschaffende informieren sich auf https://kaffeehaus.sg/kultivierter/
Besten Dank und herzliche Grüsse
Gallus Hufenus & Team
Hi Mitchell,
Happy to hear it was simple after all.
I have 3 USB-A to USB-C cables from Apple and they work very well.
I had one third-party USB-C memory card reader that failed after 10 months but since I had bought it at the Apple store, they immediately replaced it with a new and better one, even refunding me for part of the original price.
So great that we’re down to such simple issues, with Artisan itself working so well.
I trust everyone supports Artisan ;-) https://github.com/artisan-roaster-scope/artisan#donations <https://github.com/artisan-roaster-scope/artisan#donations>
Frans
> Op 22 jul. 2018, om 22:54 heeft Mitchell Rosenbaum <mitchell.rosenbaum(a)gmail.com> het volgende geschreven:
>
> Hi Frans,
>
> Ok, so you were completely correct that it was something up with the USB, possibly the adapter to USB C because when i used a different one, immediately I got a new option (see screen shot) in the Comm menu and this brought the machine on line with MODBUS.
>
> So it seems there is something going on with the adapters, seems these
> <IMG_1067.JPG>
> they are not very reliable. I will check with Coffee Tech to see if they have a direct to USB C that I can wire.
>
> In the meantime, back to roasting and thank you again!!!
>
> M
>
>
>
> On Sun, Jul 22, 2018 at 4:13 PM, Frans Goddijn <frans(a)goddijn.com <mailto:frans@goddijn.com>> wrote:
>
> Okay!
>
> Will be great to hear when all is working again, and what it was that ‘broke’
>
> F
>
>
>> Op 22 jul. 2018, om 22:05 heeft Mitchell Rosenbaum <mitchell.rosenbaum(a)gmail.com <mailto:mitchell.rosenbaum@gmail.com>> het volgende geschreven:
>>
>> Got it, thank you Frans, very much appreciate this!
>> Will dig into it and see what i can figure out.
>>
>> As far as yanking the cord on the FZ, I treat it very gently. But there is an adapter for from USB to USB C to be compatible. Maybe there is something to that, I will swap in a new adapter.
>>
>> I do see other things on the Comm Port menu like my bluetooth speaker when FZ is connected or not. But now that I see your drop down picture, the usbserial and the FT232R one looks very familiar, I feel like i have seen those before my problem started. I will try and see if that was the issue.
>>
>> I don't think I saved my settings, (foolish of me) but there was an option for recent settings which i tried but didn't make work. I will obviously save from now on.
>>
>> Thanks again, I will write back to let you know how it went.
>>
>> Warmly,
>>
>> Mitchell
>>
>> On Sun, Jul 22, 2018 at 3:26 PM, Frans Goddijn <frans(a)goddijn.com <mailto:frans@goddijn.com>> wrote:
>>
>>
>> Begin doorgestuurd bericht:
>>
>> Van: Frans Goddijn <frans(a)goddijn.com <mailto:frans@goddijn.com>>
>> Onderwerp: Antw.: [Artisan-user] Coffee Tech FZ-94 Comm Port question
>> Datum: 22 juli 2018 om 21:21:39 CEST
>> Aan: "artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>" <artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>>
>>
>> Hi Mitchell,
>>
>>>
>>> In the meantime, since you have the same machine, would you be able to say which comm port you use from the drop down menu?
>>
>> I have modified my FZ94 to have an extra PID to regulate the heater energy with sliders and buttons, so that is an extra USB port used, different than your setup.
>>
>>> Perhaps I did make and adjustment and did not notice it
>>
>> If you have frequently made a backup of your setup (see the 4th illustration below) then you can simply load one recent version that absolutely worked. If that does not work then it is the hardware / cable / connector that needs to be fixed / replaced.
>>>
>>> And while we're here, am I wrong to think that the menu for choosing your roaster
>>> would also put in these settings automatically with the new upgrade?
>>
>> A new version will ‘inherit’ the settings you have but its important to save and note the settings anyway.
>>>
>>> As far as local hardware, the USBC ports appear to be working/talking with other devices
>>> when not hooked into the FZ 94, so I don't think it's the ports, I think it is somehow
>>> the name of the ports that I don't have correctly.
>>
>> To me it seems the USB coming from the FZ94 is not connected, or a connector is not fitted correctly, or has been yanked / damaged by frequent plugging/unplugging. You don’t seem to ‘see’ any FZ-like port info.
>>
>>
>> When the FZ94 is NOT connected I see these available ports (headphone, iPhone, other stuff):
>>
>> <--01-01com-options-notconnected-180722.jpg>
>>
>> When FZ94 connected, another port is visible:
>>
>> <--02-02-com-options-connected-180722.jpg>
>>
>> Proof that all data is working:
>>
>> <--03-03-all-working-180722.jpg>
>>
>> I save / load proven config settings here:
>>
>> <--04-04-savesettings-180722.jpg>
>>
>> _______________________________________________
>> Artisan-User mailing list
>> Artisan-User(a)lists.einfachkaffee.de <mailto:Artisan-User@lists.einfachkaffee.de>
>> unsubscribe via https://mailman.ghostdub.de/mailman/listinfo/artisan-user <https://mailman.ghostdub.de/mailman/listinfo/artisan-user>
>>
>>
>
>
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de <mailto:Artisan-User@lists.einfachkaffee.de>
> unsubscribe via https://mailman.ghostdub.de/mailman/listinfo/artisan-user <https://mailman.ghostdub.de/mailman/listinfo/artisan-user>
>
>
> <Screen Shot 2018-07-22 at 4.43.43 PM.png>
Okay!
Will be great to hear when all is working again, and what it was that ‘broke’
F
> Op 22 jul. 2018, om 22:05 heeft Mitchell Rosenbaum <mitchell.rosenbaum(a)gmail.com> het volgende geschreven:
>
> Got it, thank you Frans, very much appreciate this!
> Will dig into it and see what i can figure out.
>
> As far as yanking the cord on the FZ, I treat it very gently. But there is an adapter for from USB to USB C to be compatible. Maybe there is something to that, I will swap in a new adapter.
>
> I do see other things on the Comm Port menu like my bluetooth speaker when FZ is connected or not. But now that I see your drop down picture, the usbserial and the FT232R one looks very familiar, I feel like i have seen those before my problem started. I will try and see if that was the issue.
>
> I don't think I saved my settings, (foolish of me) but there was an option for recent settings which i tried but didn't make work. I will obviously save from now on.
>
> Thanks again, I will write back to let you know how it went.
>
> Warmly,
>
> Mitchell
>
> On Sun, Jul 22, 2018 at 3:26 PM, Frans Goddijn <frans(a)goddijn.com <mailto:frans@goddijn.com>> wrote:
>
>
> Begin doorgestuurd bericht:
>
> Van: Frans Goddijn <frans(a)goddijn.com <mailto:frans@goddijn.com>>
> Onderwerp: Antw.: [Artisan-user] Coffee Tech FZ-94 Comm Port question
> Datum: 22 juli 2018 om 21:21:39 CEST
> Aan: "artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>" <artisan-user(a)lists.einfachkaffee.de <mailto:artisan-user@lists.einfachkaffee.de>>
>
> Hi Mitchell,
>
>>
>> In the meantime, since you have the same machine, would you be able to say which comm port you use from the drop down menu?
>
> I have modified my FZ94 to have an extra PID to regulate the heater energy with sliders and buttons, so that is an extra USB port used, different than your setup.
>
>> Perhaps I did make and adjustment and did not notice it
>
> If you have frequently made a backup of your setup (see the 4th illustration below) then you can simply load one recent version that absolutely worked. If that does not work then it is the hardware / cable / connector that needs to be fixed / replaced.
>>
>> And while we're here, am I wrong to think that the menu for choosing your roaster
>> would also put in these settings automatically with the new upgrade?
>
> A new version will ‘inherit’ the settings you have but its important to save and note the settings anyway.
>>
>> As far as local hardware, the USBC ports appear to be working/talking with other devices
>> when not hooked into the FZ 94, so I don't think it's the ports, I think it is somehow
>> the name of the ports that I don't have correctly.
>
> To me it seems the USB coming from the FZ94 is not connected, or a connector is not fitted correctly, or has been yanked / damaged by frequent plugging/unplugging. You don’t seem to ‘see’ any FZ-like port info.
>
>
> When the FZ94 is NOT connected I see these available ports (headphone, iPhone, other stuff):
>
> <--01-01com-options-notconnected-180722.jpg>
>
> When FZ94 connected, another port is visible:
>
> <--02-02-com-options-connected-180722.jpg>
>
> Proof that all data is working:
>
> <--03-03-all-working-180722.jpg>
>
> I save / load proven config settings here:
>
> <--04-04-savesettings-180722.jpg>
>
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de <mailto:Artisan-User@lists.einfachkaffee.de>
> unsubscribe via https://mailman.ghostdub.de/mailman/listinfo/artisan-user <https://mailman.ghostdub.de/mailman/listinfo/artisan-user>
>
>
Begin doorgestuurd bericht:
Van: Frans Goddijn <frans(a)goddijn.com>
Onderwerp: Antw.: [Artisan-user] Coffee Tech FZ-94 Comm Port question
Datum: 22 juli 2018 om 21:21:39 CEST
Aan: "artisan-user(a)lists.einfachkaffee.de" <artisan-user(a)lists.einfachkaffee.de>
Hi Mitchell,
>
> In the meantime, since you have the same machine, would you be able to say which comm port you use from the drop down menu?
I have modified my FZ94 to have an extra PID to regulate the heater energy with sliders and buttons, so that is an extra USB port used, different than your setup.
> Perhaps I did make and adjustment and did not notice it
If you have frequently made a backup of your setup (see the 4th illustration below) then you can simply load one recent version that absolutely worked. If that does not work then it is the hardware / cable / connector that needs to be fixed / replaced.
>
> And while we're here, am I wrong to think that the menu for choosing your roaster
> would also put in these settings automatically with the new upgrade?
A new version will ‘inherit’ the settings you have but its important to save and note the settings anyway.
>
> As far as local hardware, the USBC ports appear to be working/talking with other devices
> when not hooked into the FZ 94, so I don't think it's the ports, I think it is somehow
> the name of the ports that I don't have correctly.
To me it seems the USB coming from the FZ94 is not connected, or a connector is not fitted correctly, or has been yanked / damaged by frequent plugging/unplugging. You don’t seem to ‘see’ any FZ-like port info.
When the FZ94 is NOT connected I see these available ports (headphone, iPhone, other stuff):
When FZ94 connected, another port is visible:
Proof that all data is working:
I save / load proven config settings here:
Hi Mitchell,
I have the FZ94 as well, and a Macbook Pro, High Sierra 10.13.6.
You say everything was working perfectly and then it didn’t.
Since Artisan has not been changing itself you have apparently (without noticing) changed something in the hardware yourself, or a usb cable is disconnected, or a connector has come loose.
On the Artisan side nothing can be done to help.
Your computer does not ‘see’ the FZ94 right now, so no way can Artisan solve this and you must first get that local hardware working correctly.
If you can’t sort it out, get local hardware help.
Good luck!!
Frans
> Op 22 jul. 2018, om 20:22 heeft Mitchell Rosenbaum <mitchell.rosenbaum(a)gmail.com> het volgende geschreven:
>
> Hello,
>
> I'm a hobby roaster for the moment, very much enjoying learning how to use Artisan over the last year. It's been going smoothly even though I still have tons to figure out but something happened recently that I can't seem to solve.
>
> With the new version, there is a drop-down menu to configure a few great machines and I was using this to choose my FZ 94. Everything working perfectly until yesterday the USB interface wasn't talking with my Macbook (Sierra 10.13.6) pro which has two USBC ports.
>
> I tried rebooting, re-selecting the FZ 94 but still no communication. I re-downloaded and reloaded Artisan software and still nothing.
>
> I reset the USB C ports on my Mac and this didn't work either.
>
> When I looked at the serial port dropdown, the only option was COM4 and I'm wondering if that is correct? (picture attached) I didn't see if it was different earlier when things were working. Maybe it is a different port name but I am not a knowledgeable enough computer person so after researching what I could on internet, I still couldn't figure out.
>
> Would be grateful for any suggestions.
>
> Warmly,
>
> Mitchell
>
>
> <Screen Shot 2018-07-21 at 11.15.40 PM.png>_______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> unsubscribe via https://mailman.ghostdub.de/mailman/listinfo/artisan-user