Dear Artisan user group;
I have received an error I have not seen before using a Mac with the latest solfware : Sierra with a 64 bit system.
We have installed the CP210 driver with our data logger using Omron controls.
Here is a screen shot:
Modbus Error: Read float() hex() argument can't be converted to hex@line 30521
Could it be we have the wrong driver installed?
We use to use the FT232 driver but data driver was upgraded to a new model that has worked with the CP210 driver on most models (this data logger is setup for future use with Bluetooth capabilities)
Thank You;
Randy Harper
I'm relatively new to artisan. Been using RoastLogger for years but now that
I have my phidget 1048 I don't need the camera/ocr feature anymore.
I haven't been able to locate the help file or information about the
settings under Config-Device - Phidgets tab. For instance, Async check
boxes, raw data, change etc. I've found everything on the github page, but
maybe I just haven't been successful in pinpointing the proper area to look.
Secondly- I'm roasting on a Diedrich IR-24, which has a thicker J
thermocouple than the one I've hooked up to artisan, which is a K type 1/8in
I purchased here:
https://www.automationdirect.com/adc/Shopping/Catalog/Sensors_-z-_Encoders/T
emperature_Sensors_-a-_Transmitters/Thermocouple_Sensors/Probes_(with_Lead_W
ire_Transition)/THMK-T06L06-01
The temperatures are around 30 degrees F higher on the thinner K
thermocouple than what the roaster is reporting, even though my
thermocouples in the roaster are mounted next to each other (didn't want to
piggyback on BT of the roaster to phidgets)
Does anyone have any experience in this area? Perhaps the simple fact that
the probe is thinner means the readings will be different, but I do not
know. It would appear that the readings on the roaster are accurate while
the other is much hotter.
Just getting started, and appreciate any guidance.
The info you provide is very terse.
“SF6” is probably http://www.sanfranroaster.com/sf-6lb <http://www.sanfranroaster.com/sf-6lb>
And “Watlow" I assume to mean http://www.watlow.com/products/controllers/temperature.cfm <http://www.watlow.com/products/controllers/temperature.cfm>
My hunch is you maybe just connected the cables without making sure that variables like baud speed, even/uneven, parity, stopbits are all set exactly the same on both ends.
SF should be providing that info / assistance in their manuals / service desk.
Frans
> Op 29 sep. 2015, om 02:28 heeft Nate White <wcrcompany(a)gmail.com> het volgende geschreven:
>
> Which is Modbus Error: readfloat() Modbus Error: [connection] failed to connect [rtu baud[9600]] Aline 23885
>
> This is on an SF6 with Watlow. I'm sure this is a stupid question, my apologies.
>
> Nate
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> https://lists.mokelbu.de/listinfo/artisan-user
Can anyone tell me if the current version of Artisan still works with Widows 7? If not is there a place I can download an older version?
Thank You;
Randy Harper
Remove please!
> Am 25.11.2017 um 12:00 schrieb artisan-user-request(a)lists.einfachkaffee.de:
>
> Send Artisan-User mailing list submissions to
> artisan-user(a)lists.einfachkaffee.de
>
> To subscribe or unsubscribe via the World Wide Web, visit
> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
> or, via email, send a message with subject or body 'help' to
> artisan-user-request(a)lists.einfachkaffee.de
>
> You can reach the person managing the list at
> artisan-user-owner(a)lists.einfachkaffee.de
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Artisan-User digest..."
>
>
> Today's Topics:
>
> 1. Re: Artisan-User Digest, Vol 77, Issue 8 (Matthias Hoppenworth)
> 2. Re: Artisan 1.1.0 (2) on macOS 10.13 High Sierra stops
> recording (Frans Goddijn)
> 3. Re: Artisan-User Digest, Vol 77, Issue 8 (Frans Goddijn)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 24 Nov 2017 15:02:35 +0100
> From: Matthias Hoppenworth <matthias(a)hoppenworth-ploch.de>
> To: artisan-user(a)lists.einfachkaffee.de
> Subject: Re: [Artisan-user] Artisan-User Digest, Vol 77, Issue 8
> Message-ID:
> <61A32320-A53E-4FE1-AD67-3F7888EA4D8F(a)hoppenworth-ploch.de>
> Content-Type: text/plain; charset=utf-8
>
> remove please!
>
>> Am 24.11.2017 um 12:00 schrieb artisan-user-request(a)lists.einfachkaffee.de:
>>
>> Send Artisan-User mailing list submissions to
>> artisan-user(a)lists.einfachkaffee.de
>>
>> To subscribe or unsubscribe via the World Wide Web, visit
>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>> or, via email, send a message with subject or body 'help' to
>> artisan-user-request(a)lists.einfachkaffee.de
>>
>> You can reach the person managing the list at
>> artisan-user-owner(a)lists.einfachkaffee.de
>>
>> When replying, please edit your Subject line so it is more specific
>> than "Re: Contents of Artisan-User digest..."
>>
>>
>> Today's Topics:
>>
>> 1. Re: testing the noise? (Frans Goddijn)
>> 2. Re: testing the noise? (Marko Luther)
>>
>>
>> ----------------------------------------------------------------------
>>
>> Message: 1
>> Date: Thu, 23 Nov 2017 12:00:26 +0100
>> From: Frans Goddijn <frans(a)goddijn.com>
>> To: "artisan-user(a)lists.einfachkaffee.de"
>> <artisan-user(a)lists.einfachkaffee.de>
>> Subject: Re: [Artisan-user] testing the noise?
>> Message-ID: <59823D5B-0D91-44DF-95B4-7830DAB4A9D0(a)goddijn.com>
>> Content-Type: text/plain; charset=utf-8
>>
>>
>>
>>> Op 23 nov. 2017, om 04:48 heeft Dan Coplan <dan(a)fatrabbitcoffee.com> het volgende geschreven:
>>>
>>> Is there a way to test the RoR curve to adjust settings without running through beans?
>>
>> Yes. Just ‘roast’ without beans and play with energy supply and airflow to create a BT curve more or less similar to the one you aim for.
>>
>> From the graphs you post it seems that your probe is catching more noise than you want to have and earlier, the hardware and software version you used more or less smoothed this out. You could add back that smoothing in Artisan on one end or improve the reading on the other extreme end by using a heavier / thicker probe, for instance.
>>
>> Frans
>>
>>
>>
>>
>> ------------------------------
>>
>> Message: 2
>> Date: Thu, 23 Nov 2017 13:09:30 +0100
>> From: "Marko Luther" <marko.luther(a)gmx.net>
>> To: "Frans Goddijn" <frans(a)goddijn.com>
>> Cc: "artisan-user(a)lists.einfachkaffee.de"
>> <artisan-user(a)lists.einfachkaffee.de>
>> Subject: Re: [Artisan-user] testing the noise?
>> Message-ID:
>> <trinity-950c4d84-c235-4ddb-b16a-6fd32323d8a3-1511438970426@3c-app-gmx-bs42>
>>
>> Content-Type: text/plain; charset="utf-8"
>>
>> An HTML attachment was scrubbed...
>> URL: <http://mailman.ghostdub.de/pipermail/artisan-user/attachments/20171123/0fab…>
>>
>> ------------------------------
>>
>> Subject: Digest Footer
>>
>> _______________________________________________
>> Artisan-User mailing list
>> Artisan-User(a)lists.einfachkaffee.de
>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>>
>>
>> ------------------------------
>>
>> End of Artisan-User Digest, Vol 77, Issue 8
>> *******************************************
>
>
>
>
> ------------------------------
>
> Message: 2
> Date: Fri, 24 Nov 2017 15:08:52 +0100
> From: Frans Goddijn <frans(a)goddijn.com>
> To: "artisan-user(a)lists.einfachkaffee.de"
> <artisan-user(a)lists.einfachkaffee.de>
> Subject: Re: [Artisan-user] Artisan 1.1.0 (2) on macOS 10.13 High
> Sierra stops recording
> Message-ID: <7E04EA0E-EEB6-4D36-A363-0DFA4D54351D(a)goddijn.com>
> Content-Type: text/plain; charset=utf-8
>
> Hi Mischa,
>
> Happy to hear back from you about this issue!
>
> I understand in an upcoming version of Artisan, the program will allow extra moments to re-establish a connection if the data flow has been interrupted by some external glitch.
>
> Best,
>
> Frans
>
>
>
>> Op 24 nov. 2017, om 14:52 heeft machius <machius(a)me.com> het volgende geschreven:
>>
>> Hi Frans,
>>
>> Sorry for the late reply, but I only now got around to roasting again. It worked fine this time, so I assume it is indeed a glitch in the electrical system somewhere.
>>
>> Thanks for the suggestion!
>>
>> Cheers,
>> Mischa
>>
>>
>>> On Nov 13, 2017, at 9:53 PM, Frans Goddijn <frans(a)goddijn.com> wrote:
>>>
>>> Hi "MM / Machius" (why anonymous?)
>>>
>>> A similar thing happened to me once but when I looked back on what was happening, I had just clicked/switched off three 1kW elements and the interference of that on the circuitry may have disturbed communications in the wires to the laptop. Earlier, a similar thing happened when I had accidentally disconnected one of the USB cables and plugged it back in.
>>>
>>> Maybe if you analyse what’s happening when such a disturbance occurs, you can also conclude what might have caused it.
>>>
>>> If it happens at 5:30 into the roasts you could check what else happens around that time. If you post the profiles of the times it happened and details of the machine then someone might recognise it.
>>>
>>> It’s probably also good to not have other programs running on the same laptop at the same time.
>>>
>>> Frans
>>>
>>>> Op 13 nov. 2017, om 23:01 heeft machius <machius(a)me.com> het volgende geschreven:
>>>>
>>>> Y’all,
>>>>
>>>> I am running Artisan 1.1.0 (2) on macOS 10.13 High Sierra. During my two roasts in this environment, Artisan stopped recording temperatures about 5.5 minutes into the roast. The time index advances fine, which means Artisan isn't crashing (completely). Has anyone seen a similar behavior? I have not been able to determine whether any factors might have caused this behavior other than perhaps an incompatibility between the Artisan and OS versions.
>>>>
>>>> Many thanks in advance!
>>>>
>>>> Cheers,
>>>> MM
>>>>
>>>>
>>>> _______________________________________________
>>>> Artisan-User mailing list
>>>> Artisan-User(a)lists.einfachkaffee.de
>>>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>>>
>>>
>>> _______________________________________________
>>> Artisan-User mailing list
>>> Artisan-User(a)lists.einfachkaffee.de
>>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>>
>
>
>
>
> ------------------------------
>
> Message: 3
> Date: Fri, 24 Nov 2017 15:14:22 +0100
> From: Frans Goddijn <frans(a)goddijn.com>
> To: "artisan-user(a)lists.einfachkaffee.de"
> <artisan-user(a)lists.einfachkaffee.de>
> Subject: Re: [Artisan-user] Artisan-User Digest, Vol 77, Issue 8
> Message-ID: <43E4FD5C-A4FD-4003-B3ED-36904276544F(a)goddijn.com>
> Content-Type: text/plain; charset=us-ascii
>
> Hallo Matthias,
>
>
>> Op 24 nov. 2017, om 15:02 heeft Matthias Hoppenworth <matthias(a)hoppenworth-ploch.de> het volgende geschreven:
>>
>> remove please!
>
>
> If you mean to say that you want to unsubscribe / leave you can do that just as easily as the way you joined / subscribed before.
>
> Just read the information and use that.
>
> Frans
>
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>
>
> ------------------------------
>
> End of Artisan-User Digest, Vol 77, Issue 9
> *******************************************
remove please!
> Am 24.11.2017 um 12:00 schrieb artisan-user-request(a)lists.einfachkaffee.de:
>
> Send Artisan-User mailing list submissions to
> artisan-user(a)lists.einfachkaffee.de
>
> To subscribe or unsubscribe via the World Wide Web, visit
> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
> or, via email, send a message with subject or body 'help' to
> artisan-user-request(a)lists.einfachkaffee.de
>
> You can reach the person managing the list at
> artisan-user-owner(a)lists.einfachkaffee.de
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Artisan-User digest..."
>
>
> Today's Topics:
>
> 1. Re: testing the noise? (Frans Goddijn)
> 2. Re: testing the noise? (Marko Luther)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Thu, 23 Nov 2017 12:00:26 +0100
> From: Frans Goddijn <frans(a)goddijn.com>
> To: "artisan-user(a)lists.einfachkaffee.de"
> <artisan-user(a)lists.einfachkaffee.de>
> Subject: Re: [Artisan-user] testing the noise?
> Message-ID: <59823D5B-0D91-44DF-95B4-7830DAB4A9D0(a)goddijn.com>
> Content-Type: text/plain; charset=utf-8
>
>
>
>> Op 23 nov. 2017, om 04:48 heeft Dan Coplan <dan(a)fatrabbitcoffee.com> het volgende geschreven:
>>
>> Is there a way to test the RoR curve to adjust settings without running through beans?
>
> Yes. Just ‘roast’ without beans and play with energy supply and airflow to create a BT curve more or less similar to the one you aim for.
>
> From the graphs you post it seems that your probe is catching more noise than you want to have and earlier, the hardware and software version you used more or less smoothed this out. You could add back that smoothing in Artisan on one end or improve the reading on the other extreme end by using a heavier / thicker probe, for instance.
>
> Frans
>
>
>
>
> ------------------------------
>
> Message: 2
> Date: Thu, 23 Nov 2017 13:09:30 +0100
> From: "Marko Luther" <marko.luther(a)gmx.net>
> To: "Frans Goddijn" <frans(a)goddijn.com>
> Cc: "artisan-user(a)lists.einfachkaffee.de"
> <artisan-user(a)lists.einfachkaffee.de>
> Subject: Re: [Artisan-user] testing the noise?
> Message-ID:
> <trinity-950c4d84-c235-4ddb-b16a-6fd32323d8a3-1511438970426@3c-app-gmx-bs42>
>
> Content-Type: text/plain; charset="utf-8"
>
> An HTML attachment was scrubbed...
> URL: <http://mailman.ghostdub.de/pipermail/artisan-user/attachments/20171123/0fab…>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> Artisan-User mailing list
> Artisan-User(a)lists.einfachkaffee.de
> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>
>
> ------------------------------
>
> End of Artisan-User Digest, Vol 77, Issue 8
> *******************************************
Hi Mischa,
Happy to hear back from you about this issue!
I understand in an upcoming version of Artisan, the program will allow extra moments to re-establish a connection if the data flow has been interrupted by some external glitch.
Best,
Frans
> Op 24 nov. 2017, om 14:52 heeft machius <machius(a)me.com> het volgende geschreven:
>
> Hi Frans,
>
> Sorry for the late reply, but I only now got around to roasting again. It worked fine this time, so I assume it is indeed a glitch in the electrical system somewhere.
>
> Thanks for the suggestion!
>
> Cheers,
> Mischa
>
>
>> On Nov 13, 2017, at 9:53 PM, Frans Goddijn <frans(a)goddijn.com> wrote:
>>
>> Hi "MM / Machius" (why anonymous?)
>>
>> A similar thing happened to me once but when I looked back on what was happening, I had just clicked/switched off three 1kW elements and the interference of that on the circuitry may have disturbed communications in the wires to the laptop. Earlier, a similar thing happened when I had accidentally disconnected one of the USB cables and plugged it back in.
>>
>> Maybe if you analyse what’s happening when such a disturbance occurs, you can also conclude what might have caused it.
>>
>> If it happens at 5:30 into the roasts you could check what else happens around that time. If you post the profiles of the times it happened and details of the machine then someone might recognise it.
>>
>> It’s probably also good to not have other programs running on the same laptop at the same time.
>>
>> Frans
>>
>>> Op 13 nov. 2017, om 23:01 heeft machius <machius(a)me.com> het volgende geschreven:
>>>
>>> Y’all,
>>>
>>> I am running Artisan 1.1.0 (2) on macOS 10.13 High Sierra. During my two roasts in this environment, Artisan stopped recording temperatures about 5.5 minutes into the roast. The time index advances fine, which means Artisan isn't crashing (completely). Has anyone seen a similar behavior? I have not been able to determine whether any factors might have caused this behavior other than perhaps an incompatibility between the Artisan and OS versions.
>>>
>>> Many thanks in advance!
>>>
>>> Cheers,
>>> MM
>>>
>>>
>>> _______________________________________________
>>> Artisan-User mailing list
>>> Artisan-User(a)lists.einfachkaffee.de
>>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>>
>>
>> _______________________________________________
>> Artisan-User mailing list
>> Artisan-User(a)lists.einfachkaffee.de
>> https://mailman.ghostdub.de/mailman/listinfo/artisan-user
>
Hello Guys.
I friend of My And I are wonder if artisan can work as a slave of ModBus RTU. So we could use Artisan without the phidget for ATILLA Roaster with Touch screen panel.
We are using an IHM as master and need to use Artisan as slave using ModBus RTU.
Do you think is it possible ?
And if so how ?
Best regards.
Att.
Elvio Junior
